I have been loving the look of these trays for some time, but to buy one they are rather expensive…I think! A few days ago my new IG friend Jennifer of @downshilohroad posted a tiered tray she had DIY’d.
She inspired me to make one of my own!….
I bought my wood chargers and finial at Hobby Lobby using my 40% off coupon (I was too impatient to wait on them to go on sale) I bought the spindle and the feet at Menards. The home improvement stores have a few different options for parts, porch spindles, furniture legs, dowel rods, stairway ballisters. So let your imagination run wild and think outside the box!
I chose to screw my pieces together. (Partly because DH always wants things built like a tank…) so I used 1/4″ x 2″ plain dowel screw (that is a screw with threads on both ends) between the finial, top charger and top of the spindle. Then a 1/4″ lag screw between the bottom charger and the bottom end of the spindle …
I did however use gorilla super glue for the feet and they seem to be attached securely. So if you don’t want to get the drill out and buy the special screws try some super glue!
We drilled pilot holes in all the pieces before screwing the pieces together for a ‘dry fit’ .
After I was happy with the configuration I took it apart to make it easier to paint. I just used some old white flat paint we had leftover and did a couple thin coats.
After the paint dried overnight I distressed the edges on all the pieces.
After they were all distressed I topcoated it with a walnut stain making sure to really rub it in on the distressed areas.
After the stain dried I put it back together, then had some fun styling it!I really am happy with the way it turned out. I think it has a Restoration Hardware kinda feel to it! Plus I have less than $20 in mine!!! So don’t be afraid to make yourself a tiered tray and you can paint or stain it any way you want to fit into your home!
Would love to see your tiered trays if you decide to make one of your own! Post a picture in the comments or you can find me on Instagram @karen.says
I have been admiring in stores, on Pinterest and Instagram driftwood mirrors for some time. But to buy one of these mirrors it would have been well over $100 and I knew I could put one together myself for much less! Not to mention it would be more meaningful to use driftwood I collected myself while on vacation. So a couple years ago I started collecting driftwood during our summer beach vacations on Lake Michigan. Every time I would bring a piece back from a walk my husband would say we don’t need another piece of driftwood. Part of the reason he grumbled so much was the fact that our beach is 222 steps down the bluff, which means it’s 222 steps to carry the driftwood back up to the house on the bluff…:O
So I finally decided to put together my driftwood mirror a few days ago and I love the way it turned out! Here are the steps of how I put my mirror together:
Here’s all the driftwood…looks like a lot but I used most of it..
I bought a 12″ mirror at the craft store
I laid it out first to see if I had enough driftwood and to decide how I wanted it to look.
I had my husband cut a board just slightly bigger than the mirror. We left it square since the driftwood would cover it up anyway. I painted it to mimick the color of the wood. I used a light and dark gray along with tan and applied with a dry brush technique
I attached the mirror in the center of the board with liquid nails. This takes a few minutes to set up so you can re-position it if needed.
After the mirror is attached I began to layout the driftwood with the longest pieces first. I also used a paper plate to help me keep my placement even around the outside of the mirror. I used my hot glue gun to attach the driftwood to the wood backer board.
I kept gluing pieces until I had the whole board covered then began layering smaller pieces in between to hide any open spots.
After I finished I attached a saw tooth hanger to the back and hung it up in my family room where I get to look at it every day and remember our family trips to the beach!